Weidmuller WI-I/O 9-K: Wireless I/O Transmitter v1.9 Manuel d'utilisateur

For WI-I/O 9-1,2,3,4, products, refer to separate User Manuals Weidmuller, Inc., Richmond, VA 23236 Tel: (800) 8

WI-I/O 9-K v1.9 Page 10 be configured for each input-to-output link. The configuration is done at the WI-I/O K module where the input

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 11 2 OPERATION 2.1 Normal Operation Once configured using the WI-I/O K configuration softw

WI-I/O 9-K v1.9 Page 12 input during the next 30 seconds, regardless of changes to the input signal. Note that paralysi

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 13 Each pulse input is counted as two 16 bit registers. The first register is the pulse cou

WI-I/O 9-K v1.9 Page 14 Overview: • Pulse inputs are counted as 2 x 16 bit registers. • Pulse count is transmitted when the count has

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 15 50% if the level is decreasing. If an incremental shaft encoder is used, then the rate

WI-I/O 9-K v1.9 Page 16 When the WI-I/O K takes a measurement, it will transmit the analog value if the value has chan

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 17 • Analog value is transmitted if the measured value has increased by the configured sens

WI-I/O 9-K v1.9 Page 18 This indication is however available at the receiving WI-I/O 9-x by using the WI-I/O 9-x Output Reset on Comms

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 19 number of update transmissions per hour. The probability of success for an individual mes

WI-I/O 9-K v1.9 Page 2 Thank you for your selection of the WI-I/O 9-K product. We trust it will give you many years of valuable serv

WI-I/O 9-K v1.9 Page 20 20+km in Australia/NZ (1W RF power permitted). To achieve these distance, at least one site needs to be eleva

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 21 Digital input Update time, off state 1 day Update time, on state 15 minutes

WI-I/O 9-K v1.9 Page 22 Power for pulse input Average pulse rate is 1 pulse per hour (0.0003Hz), so power required = 0.06 x 0.0003 per

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 23 3 HARDWARE INSTALLATION WARNING! 110/220/240V mains power must NOT be connected to

WI-I/O 9-K v1.9 Page 24 connect to an earthed surface. If this is not possible, use an earth lug in the mounting screw connection and

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 25 YU6/900 10dBi Yagi directional antenna with N-type connector YU16/900 15dBi Yagi direc

WI-I/O 9-K v1.9 Page 26 3.2.1 Dipole and Collinear antennas. A collinear antenna transmits the same amount of radio power in all di

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 27 the common (or “central” station should have a dipole or collinear (non-directional) ant

WI-I/O 9-K v1.9 Page 28 ⊂ ⊂ + - 5.4 - 30 VDC WI-I/O K EXT SUPPLY GND 1 amp ⊂ ⊂ + - BATTERY CHARGER WI-I/O K EXT SUPPLY GND 1 a

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 29 3.4.2 Battery Pack WI-BP-I/O-9-K The WI-BP-I/O-9-K can be installed underneath the WI-I/

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 3 FCC Notice: WI-I/O 9-K Wireless Module This Users Manual is for the WI-I/O 9-K w

WI-I/O 9-K v1.9 Page 30 is typically 15 to 120 °F (-10 to 50 °C). Special “industrial” batteries, such as Eveready EN91, have a wider

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 31 3.5 Input Signal Connections 3.5.1 Digital/Pulse Inputs Digital and pulse inputs share

WI-I/O 9-K v1.9 Page 32 ⊂ ⊂ GND AI- WI-I/O K ⊂ ⊂ + - AI+ WI-I/O K ⊂ LOOP POWERED TRANSDUCER EXTERNALLY POWERED TRANSDUCER ⊂ ⊂ ⊂ + - A

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 33 connecting to the WI-I/O K module. 3.5.4 RS232 serial port An RS232 port is provided for

WI-I/O 9-K v1.9 Page 34 4 CONFIGURATION The WI-I/O K module is configured by creating a configuration file on a PC and downloading to

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 35 4.1 I/O Mapping Enter I/O mappings as per the WI-I/O 9-x manual. In the following exam

WI-I/O 9-K v1.9 Page 36 4.2 Update Transmission Times Each input signal has an update time. If a change has not occurred for this

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 37 message during the paralysis time - this is to prevent overcrowding of the radio channel.

WI-I/O 9-K v1.9 Page 38 supply. Consider the above example, with WI-I/O K #14. T his module is mounted on a water tank, and the ana

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 39 4.6 Supply Voltage The supply voltage may be mapped as an internal analog input. The 16

WI-I/O 9-K v1.9 Page 4 Important Notice Weidmuller, Inc. products are designed to be used in industrial environments, by experienced i

WI-I/O 9-K v1.9 Page 40 4.7 Pulse Inputs Each WI-I/O K has two pulse inputs. Each pulse input has 2 x 16 bit counters and a calculate

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 41 Example 1: A turbine meter is connected to a WI-I/O K with a pulse signal of 15 pulses pe

WI-I/O 9-K v1.9 Page 42 Example 2: A system of tipping bucket raingauges is installed to monitor rainfall in a catchment area. Each ra

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 43 4.7.1 Manually Setting Counter Values The values in the counters can be manually set to

WI-I/O 9-K v1.9 Page 44 100% value at 50Hz. The maximum pulse rate can be configured from 0.02 Hz to 1000Hz. For shaft encoder inputs,

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 45 Loading Configuration from a Module Care should be taken when loading a configuration f

WI-I/O 9-K v1.9 Page 46 5 DIAGNOSTICS AND TESTING 5.1 System Problems Most problems relate to incorrect configuration, or radio pa

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 47 Note : The OK LED will generally not light continuously unless the cable is

WI-I/O 9-K v1.9 Page 48 below. The counter values will display both base and Hi counters as a 32 bit number, but in “decimal” format.

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 49 6. Now adjust the signal to the maximum value (100%). Select “Process High Value”. 7.

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 5 Limited Warranty, Disclaimer and Limitation of Remedies Weidmuller, Inc. products are wa

WI-I/O 9-K v1.9 Page 50 6 SPECIFICATIONS General EMC approval FCC Part 15 Radio standards USA FCC Part 15.247 Canada RSS-210

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 51 Analogue loop supply Internal DC converter 24V DC Nominal, 50mA Low Battery voltage st

WI-I/O 9-K v1.9 Page 52 configurable 0.5-100 seconds. Analogue Input Setpoint Configurable high & low setpoint may be transmit

User Manual Manual WI-I/O K_1.4 Page 53 7 WARRANTY We are pleased that you have purchased this product. Weidmuller, Inc. products are

WI-I/O 9-K v1.9 Page 6 WI-I/O 9-K Radio Telemetry Module USER MANUAL 1 OVERVIEW ----------------------------------------------------

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 7 3.5 Input Signal Connections...

WI-I/O 9-K v1.9 Page 8 1 OVERVIEW Note: Please refer to separate User Manuals for the WI-I/O 9-1,2,3,4 products. The WI-I/O 9-K pro

User Manual v1.9 Manual WI-I/O 9-K v1.9 Page 9 Digital Signals Examples: motor fault, tank overflow, intruder alarm Pulse signals - use