Weidmuller SL-MOD-GW Manuel d'utilisateur

SL-MOD-GWModbus/TCP GatewayUsermanual

4 UMSLMODGW-1006The following table outlines the indicator condition and the corresponding status after the power-on self testhas been completed:LED F

UMSLMODGW-1006 53.Installation3.1 Regulatory notes1. The SL-MOD-GW is suitable for use in non-hazardous locations only.2. The SL-MOD-GW is not author

6 UMSLMODGW-10066. Once you are certain that all connections have been made properly, restore the power.3.4 DIN rail mounting and removalThe SL-MOD-GW

UMSLMODGW-1006 73.6 Powering the SL-MOD-GWBefore connecting power please follow the rules in the section called “Safety Precautions” andSectio

8 UMSLMODGW-1006• Stub connections off the main line should be avoided if possible or at least be kept as short as possible. Stubconnections must not

UMSLMODGW-1006 93.9 Connecting EthernetThe following table describes the 10BASE-T Ethernet RJ-45 connector pinout: TX+TX-RX-RX+1Pin Signal Function1

10 UMSLMODGW-1006

UMSLMODGW-1006 114.Ethernet & IP configurationBefore configuring the SL-MOD-GW, obtain a unique static IP address, subnet mask, and default

12 UMSLMODGW-10069.Type SETIP, then press Enter within 10 seconds after the prompt is shown:DIAG MODEVer: x.yS/N: 1234MAC: 00:50:C7:67:71:97IP Address

UMSLMODGW-1006 13This will show the Local Area Connection Properties Dialog:3.Select the Internet Protocol (TCP/IP) entry and click on Proper

SL-MOD-GWModbus/TCP Gateway: User manualNo part of this material may be reproduced or transmitted in any form or by any means or used to make any deri

14 UMSLMODGW-1006

UMSLMODGW-1006 155.Web browser based managementThe SL-MOD-GW incorporates an embedded web server. This allows you to connect to the device and monito

16 UMSLMODGW-1006Use the menu bar shown on the left side to navigate the different pages.NoteIn order to connect to the SL-MOD-GW via TCP/IP, your PC

UMSLMODGW-1006 17Reset to factory defaultsThis alarm indicates that the device' configuration data was reset to factory defaults. The device requ

18 UMSLMODGW-1006CRC errorsA counter that increments each time a message is received that has a CRC that does not match what iscalculated. Typically t

UMSLMODGW-1006 19Serial numberThe serial number of the SL-MOD-GW. The serial number is specific to your device.5.3 Configuring and commissioningThe co

20 UMSLMODGW-1006Once you click Save the new settings are stored and applied instantly. The new settings are confirmed withthe following page:Illustra

UMSLMODGW-1006 21Data bitsOnly 8 data bits can be selected here which is a requirement for RTU.Stop bitsCan be configured to be 1 or 2. The Modbus

22 UMSLMODGW-1006

UMSLMODGW-1006 236.DecommissioningBefore disconnecting the unit please follow the rules in the section called “Safety Precautions”.6.1 Disconnecting1

UMSLMODGW-1006 iiiContentsImportant user information ...

24 UMSLMODGW-1006

UMSLMODGW-1006 25AppendixA.SpecificationsSL-MOD-GW Modbus/TCP GatewayInterfacesEthernet 1Serial ports 1, software configurable as either 1 x RS-232

26 UMSLMODGW-1006Emissions (radiated and conducted) AS/NZS CISPR 22 / EN 55022 (Class A)Immunity EN 55024Electrostatic discharge EN 61000-4-2Radiated

UMSLMODGW-1006 27A.1 Dimensions101.0 mm120.0 mm3.98 in4.72 in0.89 in22.5 mm101.0 mm3.98 inIllustration A.1: Enclosure dimensions

28 UMSLMODGW-1006

UMSLMODGW-1006 29Glossary10BASE-T10 Mbit/s twisted pair Ethernet standard.Standardized in IEEE 802.3iAPIPAAutomatic Private IP AddressingClass AC

30 UMSLMODGW-1006RS-422See EIA-422.RS-485See EIA-485.Subnet maskA numeric address used in conjunction with anIP address to segment network

UMSLMODGW-1006 31IndexAAbout, 18Accumulative connections, 17BBaud rate, 20Brown out reset, 16CcableRS-232, 8RS-422, 8RS-485, 8cable lengthEthernet len

32 UMSLMODGW-1006removal, 6Replies, 17Requests, 17Reset to factory defaults, 17restart, 21RJ-45, 9RS-232, 8RS-422, 7RS-485, 7run-time faults, 16Rx tim

UMSLMODGW-1006 33ReferencesName: WeidmllerCompany: Weidmller Australia Pty LtdStreet Address: 43 Huntingwood Drive,Postcode: 2148Suburb: Huntingwood,

iv UMSLMODGW-1006Tables2.1 LED diagnostic codes ...

34 UMSLMODGW-1006

UMSLMODGW-1006 vImportant user informationThis manual explains how to install, operate and configure a SL-MOD-GW. This device may only be used forthe

vi UMSLMODGW-1006Document conventionsThroughout this manual we use the following symbols and typefaces to make you aware of safety or otherimportant c

UMSLMODGW-1006 11.IntroductionThe SL-MOD-GW is a Modbus/TCP to Modbus RTU gateway.The gateway features one serial port which can be configured as eit

2 UMSLMODGW-10061.1 FeaturesThe SL-MOD-GW gateway provides the following key features:• Modbus/TCP protocol (Ethernet)• Modbus RTU protocol (either RS

UMSLMODGW-1006 32.DescriptionThe power and RS-485/RS-422 terminals are placed on the top side of the unit. The RS-232 and Ethernetconnectors are plac